|
By Duck - 16 Years Ago
|
|
Fellas- The fun never ends; Today I went to get an expansion plug to use in the hole in the head (rear) across from the water temp sending unit. The brain trust at my local NAPA informed me that no, I need 4 plugs in the heads, not just one. They also told me the size of these plugs was 1.788, which I recognize as the size plugs for the block. I stood there repeating myself until the counter person told me I didn't know what I was talking about, at which point I left empty-handed. I had nearly the same experience across town at the Carquest store.Would someone happen to know the correct size of the plug, so I can try it that way tomorrow? Maybe I'll have better luck doing it that way... Thanks, /Duck
|
|
By 62galxe - 16 Years Ago
|
|
im fixing to tackle that challange. finally got the right water pump. evidently the parts guy on the phone assumed i was stupid. asked for a 292 pump and he ordered me a 289 pump. they dont know what a 292 is. well off to chase down the plug.
|
|
By Duck - 16 Years Ago
|
|
Kenny- Been there, done that. Finally got sick of it all and ended up sending the pump I had to Cardone for a rebuild. $92.00 later I am a much wiser (albeit, poorer) man.... -Good Luck- /Duck
|
|
By Hoosier Hurricane - 16 Years Ago
|
|
Duck, Kenny: The head plug is 59/64. The NAPA number is 2193077.
|
|
By Duck - 16 Years Ago
|
|
John- Thank you! I wish you would consider working full time at my local NAPA- They could REALLY use your help... -Thanks Again- /Duck
|
|
By simplyconnected - 16 Years Ago
|
|
Yep! It goes on the back of the engine. I installed brass. Here's a picture: 
|
|
By PF Arcand - 16 Years Ago
|
|
Duck: Hopefully your head isn't corroded badly at the opening. According to John Mummert, he has seen heads that won't hold a plug..
|
|
By 62galxe - 16 Years Ago
|
thanks for the napa number. autozone needs year make and model so they can look at there computor and tell me im asking for the wrong size. they cant go to shelf and look. ok now to give duck back his thread.
|
|
By Hoosier Hurricane - 16 Years Ago
|
|
Kenny: Actually, in the mid 70s I did work at NAPA as the machinist. That was when they had catalogs. You know, paper books with printing in them. No screens or keyboards. Mixture of older guys and young guys, and the older experienced guys helping the young guys when they hit a snag. I still have a couple of their catalogs, that's where I come up with part numbers. I am no longer associated with NAPA, and am not pushing their parts, though I do use them myself. Some of the other stores can cross over the NAPA numbers for you.
|
|
By charliemccraney - 16 Years Ago
|
|
I always provide the part numbers. Just go to their website, look up the parts, write down the numbers. They usually have a picture of the part, too. I've never had a problem doing it this way. If I do, I'll know, without a doubt, who to blame.
|
|
By mctim64 - 16 Years Ago
|
|
Duck, of course the plugs they were trying to sell you were the ones that go in the ends of the heads on the early model Ys. 1 3/4"
|
|
By aussiebill - 16 Years Ago
|
|
Duck and guys, for the small welch plug at end of intake side of heads i have been using for years a 23 mm welch plug, nowadays the metric size is easier to find here than the original odd size. Hope this may help. best regards aussiebill.
|