|
By 1964fordf100292 - 13 Years Ago
|
|
hey guys. I am hoping that you can tell me what i got. I bought a 4bbl manifold off of ebay and was advertised as a ecz-9425-b. when I got it, the first thing i did was verify that it was a B manifold and it is but here is where it gets bewildering. the carb mounting flange does notlook like the holley type carb spacer. it looks like the teapot flange. is it possible to have a b manifold with a teapot carb flange?
|
|
By GREENBIRD56 - 13 Years Ago
|
|
I'm afraid there is also an ECB-9425-B that has the teapot base. At the passenger side of the carb base is a good sized opening for the choke????? Use a wire brush on the part number lettering and re-check the last letter of the prefix. Maybe if incorrectly listed - you might return it?????
|
|
By 1964fordf100292 - 13 Years Ago
|
|
ya. it's a ecb not a ecz. not gonna return it. prolly just get a adapter. where can i get one at that goes from the teapot to the modern holley.
|
|
By charliemccraney - 13 Years Ago
|
|
Is the F-Code intake a unique casting or a B intake machined differently?
|
|
By Hoosier Hurricane - 13 Years Ago
|
|
The F code is EDB-D, used only on the supercharged engines. It has both bolt patterns on it.
|
|
By GREENBIRD56 - 13 Years Ago
|
|
64f100 - Check out Speedway Motors p/n 1351935B - $20 Just make sure you smooth up the edges under the throttle blades when you mount everything.
|
|
By The Master Cylinder - 13 Years Ago
|
GREENBIRD56, I'm liking your new Avatar. Looks kinda like Mr. Horsepower (Clay Smith Cams http://claysmithcams.com/) but GREEN!!! 
|
|
By Hoosier Hurricane - 13 Years Ago
|
|
Oops! F code is EDB-F, not D. D is the head designation. Brain fade. Old timers. Sorry.
|
|
By 1964fordf100292 - 13 Years Ago
|
|
thanks for the help guys. Ya know, I posted the same question on here and on ford-trucks.com and you are the only ones who responded and gave me help. thanks again. you guys are the greatest. now i just needto find a 1.08 autolite 4100 to go one this intake.
|
|
By PF Arcand - 13 Years Ago
|
|
1964; If the intake isn't what was advertised, I don't know why you are not asking to return it? You can register a complaint with e bay if refused.. looking for an Autolite carb, try a Mustang club, or if you want a rebuilt, try Pony Carburetors in N.Y. state. However, they like to get a core or they charge extra..
|
|
By pegleg - 13 Years Ago
|
|
Hoosier Hurricane (2/5/2012)
Oops! F code is EDB-F, not D. D is the head designation. Brain fade. Old timers. Sorry.John's correct. The F code intake is the later intake with material added to the carb pad and the Lincoln style blower carb bolt pattern added. They have both carb bolt down patterns machined. the carb pad is approximately 3/16" higher than the B and is noticeable by looking at the intake. They are also machined for the Blower carb throttle bores and have several notches machined and cast that are unique.
|
|
By 1964fordf100292 - 13 Years Ago
|
|
When i was looking for a "B" manifold, I wasn't looking at the whole number, just the last one. the last number/letter is a B so I bought it, so in that aspect it was as advertised. I made the goof up. But i can make it work so no biggie. I'll get the carb spacer/adapter from speedway. As far as Pony Carbs, I think they are overpriced and I ain't that rich so I'll search for a used one in need of a rebuild and go from there. Wat are your guys carb recommendations for a stock 292? what has worked for you guys. I know 500cfm is max from what i have read.
|
|
By 1964fordf100292 - 13 Years Ago
|
|
My original post said it was advertised as a ecz-9425-b and it wasn't. it was advertised correctly. i just didn't pay close enough attention.
|