Here is what a twin turbocharged Y-block does to a Moser 31 spline hardened axle shaft!! It is also crushing the housing.





You can see how it has been crushing the housing and bending the leaf spring pad.



Chris is showing off his enginuity. What better than a Y-BLOCK oil distribution for Twin Turbos on a Y-BLOCK that doubles as a fuel pump block off plate. He drilled through the plate so both turbo oil feeds will branch from there. It's pretty cool we think.



We got our p/s pump mounted. I bought a dual belt water pump pulley from Jegs that is for a small block ford. We just had to make the hole bigger and press the mounting pad farther onto the water pump shaft and it lined up pretty well. I seen John's set up which is nice but we have our crank trigger on the crank pulley so it would be difficult to mount another belt down there.



Going into it's new home in a 99 F150 two wheel drive.



My Y is going to be real happy in this truck. We moved the dipstick to the front location in the block because our motor mount is in the way of the old location.

What a pleasent supprise, to start a project and pour your knowledge and experience into that and then find out you created a MONSTER! Wish we all had such tough luck. Chuck

Y's guys rule!
Looking for McCullouch VS57 brackets and parts. Also looking for 28 Chrysler series 72 parts. And early Hemi parts.

MoonShadow, 292 w/McCulloch, 28 Chrysler Roadster, 354 Hemi)
Manchester, New Hampshire

I will admitted I did not plan on making this much power when I put it together. I think the diff tubes caved in before I had the ladder bars installed. We noticed an extreme difference with those installed. My new axle assembly will be built for it. Funny thing is that we are still running the stock size u-joint at the rear diff and that's been hanging in there also. My trans is an E4OD and I am installing the two wheel drive output shaft now and also installing high energy blue clutches. It was working perfectly but some of the clutches were getting a little warm. My torque converter was built for 1300 HP by Midwest Converters so hopefully that hangs in there.

It makes me curious of the condition of everything else. If memory serves, nothing in your driveline was designed for 1000hp.


Lawrenceville, GA

On my 57 I had to re-enforce the original spring pads as well. I wound up plating them with 3/16 steel and extending the rear portion back a couple inches over the spring to prevent the housing from rotating. I'd consider a 3 or 4 link or ladder bars in your case. The torque numbers are way more than leaf springs are going to be able to handle.

Frank/Rebop

Bristol, In ( by Elkhart) 

You are crossing over into gasser or altered country with that engine. Did the axles twist on that first banzai run or previously? What are you running for transmission? You are going to need a really stout driveline to handle this beast. Ok, give up, put in a straight axle front end with a nose up attitude, use the extra 5" to put in tubs and BIG slicks and go crazy! Chucik

Y's guys rule!
Looking for McCullouch VS57 brackets and parts. Also looking for 28 Chrysler series 72 parts. And early Hemi parts.

MoonShadow, 292 w/McCulloch, 28 Chrysler Roadster, 354 Hemi)
Manchester, New Hampshire

Hey everyone we are making some progress on the new build. I will have more pics tomorrow. The biggest question has been the differential, we would like to use the original diff in the 99 F150 which is an 8.8in rear diff. I was on the phone for hour today talking to people about if it would handle the power. The consensus came to that they can handle a lot of power but would be borderline for the power we are running. We thought we would just swap the diff from my 62 to that on since it has a locker and Moser 31 spline axles, but would require some modifying and the diff is about 5 inches narrower than the F150. I noticed that one of my axle seals was leaking so I removed the axle to find that those badass Moser 31 spline axles were twisted so I called Moser and they said yeah those probable aren't going to handle 1000 horsepower. So in any situation I would either need to completely rebuild my current 9in or build that 8.8in that might handle the power. So I talked to Strange Engineering and I am ordering a prebuilt custom 9in rear diff that will bolt into the 99 F150 with custom 12in rear disc brakes. It ended up being about $400 dollars more to just order a prebult brand new rear diff than modifying mine. Plus it will have the bigger late Ford rear axle bearing, Detroit locker, 35 spline axles, rear disc brakes and 3 1/2 tubes and a 10yr warranty on everything on the axle. The 35 spline axle should hold up! I will take pics of the axles tomorrow. I do have a pic of the current 9in diff housing though, it is hard to see in the pic but the leaf spring plates are actually tearing away from the axle and on the front side it is crushing the axle tube from all the hp and torque. It is awesome looking at those damaged parts that are damaged, not from abuse, but from simply too much POWER! I cannot wait for this Y to crank that F150 down the road. I will take some pics of the p/s pump bracket that Chris built and the badass turbo oil feed manifold/fuel pump cover that Chris also built.



It's hard to see but that axle is crushing in where the leaf spring pads are.

One of the great benefits of farm life there always seems to be a few spare vehicles scattered around. Especially it you are looking for pickups. We got an old chevy sedan running when I was barley a teen. Used it for a "gully racer". basicaly that meant go as fast as the crapped out old 6 cylinder would allow and up a bank to see who could go highest on roll over the neatest. Glad my parents and other relatives never caught on. We thought we were good enough to be "hell drivers". Sure, fat chance! Chuck

Y's guys rule!
Looking for McCullouch VS57 brackets and parts. Also looking for 28 Chrysler series 72 parts. And early Hemi parts.

MoonShadow, 292 w/McCulloch, 28 Chrysler Roadster, 354 Hemi)
Manchester, New Hampshire

Don't worry we won't go that crazy. The 99 F150 is a great looking truck . Me and my dad decided we will continue my build with his old 65 F100 2 wheel drive out at the farm. He slid down a hill hunting about twenty years ago and it's been sitting ever since. Nice part is all my stuff from this truck will transfer right over. My engine and transw will stay in the 99 and I will build a new y-block for the 65. I have been looking for an excuse to build another y-block. There are three up the street in a guys grage so I should be able to get ahold of one. We were thinking of using a nice noisy kenne bell on that one. We weill just mount it remotely on the side. That will be this fall.

Hutz, when I first got your message, I thought it would be even worse. That ain't bad at all. Just get a new cabin for your truck, but please don't do anything as stupid as above That red one is ugly as hel...

 Seppo from Järvenpää, Finland
www.hollowheads.net (just click the hole in the head to proceed)