Group: Forum Members
Last Active: Last Month
Posts: 398,
Visits: 81.0K
|
I have a Stewart Warner Amp Meter I want to hook up to my 12 volt system. Near as I can figure the negtative lead goes to the starter motor and the positive lead goes to the generator, but which poll on the gen? Or is there another option. Thanks, Richard
|
Group: Forum Members
Last Active: 10 Years Ago
Posts: 118,
Visits: 7.9K
|
Another option to consider in lieu of an Amp Meter is a Volt Meter. A couple of considerations would be that a VM will better reflect the status of your charging system. Another woud be that an Amp Meter would channel a lot of Amps through wiring that goes into the cockpit. Here is an idea by MAD Mark Hamilton on how to use a relay with a VM to even better monitor your electrical system.
Also, there is a lot to read on this link but some good thoughts about Amp meters. http://www.madelectrical.com/electricaltech/amp-gauges.shtml
Jim Norfolk, VA
 "MABLE" 1956 Thunderbird Green / Brown Interior (ZE-XG)
 "MEAN GREEN" 1956 Mainline (FG-BE)
|
Group: Forum Members
Last Active: 10 Years Ago
Posts: 703,
Visits: 3.1K
|
Good information. When I started rebuilding my '56 pickup the big yellow wire that went to the ampmeter was welded to all the other adjacent wires. Why there had not been a fire is beyond me.
Mark
1956 Mercury M100 1955 Ford Fairlane Club Sedan Delta, British Columbia
|
Group: Forum Members
Last Active: 3 minutes ago
Posts: 3.6K,
Visits: 497.6K
|
As Jimz said, go with a volt meter. As far as I'm concerned, an amp meter inside the car is a fire waiting to happen as evidenced by the reply above.
54 Victoria 312; 48 Ford Conv 302, 56 Bird 312 Forever Ford Midland Park, NJ
|
Group: Forum Members
Last Active: 2 Years Ago
Posts: 279,
Visits: 4.0K
|
While I wholeheartedly agree with not pulling 8 or 10 gauge wire into the cockpit and running all the current draw through a dash mounted ammeter, I was wondering if there was an affordable automotive unit that used a shunt instead of putting all current through the ammeter. I have a shunt on the boat and also on an old Sears handheld dwell/tach/volt/ammeter, so I know it's not difficult to do.
Don
|
Group: Forum Members
Last Active: 2 Years Ago
Posts: 236,
Visits: 237.6K
|
On the 56 Fairlane all the wires needed for an ampmeter are already under the dash on the back of the ignition switch. There are 2 yellow wires, 1 comes from the starter solenoid (it's 12V unfused) the other runs to the voltage regulator (also unfused) Remove the wire that runs to the solenoid and put it on 1 of the ampmeter terminals then run a 10ga jumper from the other ampmeter terminal to the location on the ignition switch that you removed the yellow wire from. The other yellow that runs to the regulator should remain on the ignition switch
What you have done is insert the ampmeter in series with the battery connection that supplys the vehicle, all discharge and charge current runs thru this yellow wire that you inserted the ampmeter into. If the ampmeter reads backward after doing this just swap the 2 wires on the back of the ampmeter to correct it's polarity.
For the guys who do not want to run high current into the car for a meter, It's already there in the factory harness, as long as your harness is in good condition and any wires you run are protected against chafing I have no problem with an ampmeter, granted a voltmeter can give you almost the same info but I had this SW combo amp/oil gauge from the 60's. A nice rectangle box that fit between the kick panel and the emergency brake and could not resist using it
|
Group: Forum Members
Last Active: 3 hours ago
Posts: 1.0K,
Visits: 163.3K
|
Let me weigh in on this. For me a voltmeter was worthless. I threw a fan belt on my 78 scruby work truck. Heard a noise, checked my gauges, had a needle in the middle of the volt gauge. When I got off the 4 lane and slowed down the truck started boiling over. If I had an ammeter I would have known right away I wasn't charging.
Dennis in Lititz PA
|
Group: Forum Members
Last Active: 3 minutes ago
Posts: 3.6K,
Visits: 497.6K
|
This is a problem where all you have is a needle, a line and nothing else. If it is a marked gauge, then you can see what the output is as it should drop down to 12 volts rather quickly rather than the 13.5 to 14.5 that it should be running at. At least that is my experience.
54 Victoria 312; 48 Ford Conv 302, 56 Bird 312 Forever Ford Midland Park, NJ
|
Group: Forum Members
Last Active: Last Year
Posts: 1.7K,
Visits: 340.0K
|
Volt meters came into use when more accessories were beginning to be used especially A/C. An AWG #10 is rated at 30 amps and can easily handle 40 amps for a time which is fine for our 50's cars but today's computer cars need more. As much as we hate them, the "idiot" light is our best friend especially when loosing a fan/generator belt. Good luck....
56 Vic, B'Ville 200 MPH Club Member, So Cal.
|
Group: Forum Members
Last Active: Last Week
Posts: 1.8K,
Visits: 194.1K
|
I'm more of a fan of voltmeters. Properly marked, they also show over voltage, and having had regulators fail and boil the battery, they let you see that coming.
That said, I've also had shunt type ammeters in marine use, on 90 amp alternators. Not the wimpy auto ones, but units 10" in diameter and 24" long, that make 90 amps all day and don't overheat. No way you run # 2 wire up to the control stations and back.
The other thing we forget in the high tech world is you can still buy fusible links. Smaller wire, non flammable insulation, designed to melt like a fuse. You need to carry spares, and a pair of pliers to crimp, but they save the harness. Find and clear the fault before you replace it. I use those at the alt/gen terminal, from the battery to the fuse panel, headlight feed, and on individual feeds. You can buy "mega circuit breakers" , but a fuse link always works, it's cheap, and it fits in the glove box. For me, it's a must have on an ammeter.
miker 55 bird, 32 cabrio F code Kent, WA Tucson, AZ
|