Profile Picture

Anyone recognize these McCulloch brackets?

Posted By Shaggy 9 Years Ago
You don't have permission to rate!
Author
Message
miker
Posted 9 Years Ago
View Quick Profile
Supercharged

Supercharged (4.1K reputation)Supercharged (4.1K reputation)Supercharged (4.1K reputation)Supercharged (4.1K reputation)Supercharged (4.1K reputation)Supercharged (4.1K reputation)Supercharged (4.1K reputation)Supercharged (4.1K reputation)Supercharged (4.1K reputation)

Group: Forum Members
Last Active: Yesterday
Posts: 1.8K, Visits: 190.8K
Shaggy, I sent a PM.

miker
55 bird, 32 cabrio F code
Kent, WA
Tucson, AZ
Shaggy
Posted 9 Years Ago
View Quick Profile
Supercharged

Supercharged (316 reputation)Supercharged (316 reputation)Supercharged (316 reputation)Supercharged (316 reputation)Supercharged (316 reputation)Supercharged (316 reputation)Supercharged (316 reputation)Supercharged (316 reputation)Supercharged (316 reputation)

Group: Forum Members
Last Active: 7 Years Ago
Posts: 123, Visits: 609
I dont see them on any of the photo's that are left on the vs57 website either, unfortunately these are probably some odd brackets then and not worth too much i'd guess... Sad As for the brackets and pulleys for my ford, i figure i can make them pretty easy. I have a bridgeport and a lathe so i'm not scared. 
Lou
Posted 9 Years Ago
View Quick Profile
Supercharged

Supercharged (1.3K reputation)Supercharged (1.3K reputation)Supercharged (1.3K reputation)Supercharged (1.3K reputation)Supercharged (1.3K reputation)Supercharged (1.3K reputation)Supercharged (1.3K reputation)Supercharged (1.3K reputation)Supercharged (1.3K reputation)

Group: Forum Members
Last Active: 3 hours ago
Posts: 558, Visits: 8.3K
Maybe a Studebaker bracket ?
MoonShadow
Posted 9 Years Ago
View Quick Profile
Supercharged

Supercharged (7.6K reputation)Supercharged (7.6K reputation)Supercharged (7.6K reputation)Supercharged (7.6K reputation)Supercharged (7.6K reputation)Supercharged (7.6K reputation)Supercharged (7.6K reputation)Supercharged (7.6K reputation)Supercharged (7.6K reputation)

Group: Forum Members
Last Active: Yesterday
Posts: 4.6K, Visits: 37.8K
This is the underhood bracket for a 56 Ford car. Like Mike mentioned not all pulleys are the same so it takes some time to put an complete setup together.
http://forums.y-blocksforever.com/uploads/images/8e9bfc3c-cc0c-4076-ac74-da7e.jpg


Y's guys rule!
Looking for McCullouch VS57 brackets and parts. Also looking for 28 Chrysler series 72 parts. And early Hemi parts.

MoonShadow, 292 w/McCulloch, 28 Chrysler Roadster, 354 Hemi)
Manchester, New Hampshire
miker
Posted 9 Years Ago
View Quick Profile
Supercharged

Supercharged (4.1K reputation)Supercharged (4.1K reputation)Supercharged (4.1K reputation)Supercharged (4.1K reputation)Supercharged (4.1K reputation)Supercharged (4.1K reputation)Supercharged (4.1K reputation)Supercharged (4.1K reputation)Supercharged (4.1K reputation)

Group: Forum Members
Last Active: Yesterday
Posts: 1.8K, Visits: 190.8K




This is the bracket I bought from Craig Conley about 2002 or so. Mounts a VS series on the driver's side. Also mounts an SN series if you use the extended pulley. The instruction manual I found on line said on a bird, relocate the p/s pump to the pass side, and move the battery.

I used it to reverse engineer a pass side bracket on the bird.

Shaggy, you around Seattle?

miker
55 bird, 32 cabrio F code
Kent, WA
Tucson, AZ
MoonShadow
Posted 9 Years Ago
View Quick Profile
Supercharged

Supercharged (7.6K reputation)Supercharged (7.6K reputation)Supercharged (7.6K reputation)Supercharged (7.6K reputation)Supercharged (7.6K reputation)Supercharged (7.6K reputation)Supercharged (7.6K reputation)Supercharged (7.6K reputation)Supercharged (7.6K reputation)

Group: Forum Members
Last Active: Yesterday
Posts: 4.6K, Visits: 37.8K
It's hard to tell. None of my reference's shows a bracket like that. Is there a number cast into it? As far as the rest goes I would be a bit leary about buying one completely disassembled. There is probably a reason it was taken apart.


Y's guys rule!
Looking for McCullouch VS57 brackets and parts. Also looking for 28 Chrysler series 72 parts. And early Hemi parts.

MoonShadow, 292 w/McCulloch, 28 Chrysler Roadster, 354 Hemi)
Manchester, New Hampshire
Shaggy
Posted 9 Years Ago
View Quick Profile
Supercharged

Supercharged (316 reputation)Supercharged (316 reputation)Supercharged (316 reputation)Supercharged (316 reputation)Supercharged (316 reputation)Supercharged (316 reputation)Supercharged (316 reputation)Supercharged (316 reputation)Supercharged (316 reputation)

Group: Forum Members
Last Active: 7 Years Ago
Posts: 123, Visits: 609
I figure there are a lot of guys on here that play with these huffers so i figure it's worth a try. He says 392 but that doesnt look right to me.

I'm asking because i'm looking for a McCulloch for the 292 in my daily and even though i'm pretty sure these brackets wont fit I may consider it if they are usable sellable or tradeable

https://seattle.craigslist.org/tac/pts/5704413460.html


Reading This Topic


Site Meter