Re the plenum at the base of the windshield, thats also why the Pontiac TA's and others usea backward facing scoop. It pulls from the high pressure area at the base of the windshield.

     Re Doug, Would seem as though the inertia of the air would have more effect than the formula gives. What am I missing?

Frank/Rebop

Bristol, In ( by Elkhart) 

The pressure at the base of the windshield idea is exactly how a '57 Ford fresh air vent works.  At 115 mph in my race car when I close the throttle, it's almost a gale force wind coming in.  And that's with all the windows closed.  With the throttle wide open, virtually no air comes in, maybe even some goes out.  Remember, I have a 4" flex hose running from the cowl plenum to the supercharger inlet.

John - "The Hoosier Hurricane"

Get a big industrial shop fan, fit a shroud to direct the air and see if you can rig it to simulate 130mph wind. This will probably only be able to work well for the forward facing scoop. Might need a real big fan to get things right for a rear facing scoop. Wait, Tim has an air plane, right. Got any spare engines and props? A friend of mine has a Lycoming aircraft engine on a stand but you're a bit too far away to borrow that.


Lawrenceville, GA

First of all  - many thanks to Doug T for adding the link to Dwyer instruments - looks like there are more than a few types available to do various jobs. I never went looking for them before for sure.

Charlie - I think something that measures in inches of water will be fine enough scale to get an idea what's happening. But I also think vibration might be more of a hazard to reading the "wet" instruments than anything else though. When I checked the mining machine pressurizers - we wanted .2-.5 inches of water minimum and that is plenty enough to knock you down when you open the door latch. We mounted the instrument at a central location and then ran tubing wherever we wanted the comparative readings. As long as the tube opening didn't have air actively blowing across the open end (larger tube cut at an angle and wrapped in gauze) - it worked as a static pressure source.

So if you mount a "comparator" style gauge under the dash on the passenger side - mount and baffle an interior pressure source for reference - and then run a "sensor" tube (or tubes) to the points where you want the comparison pressure reading ....photograph the guage during a live run?

Nascar guys have run off the plenum at the base of the windshield forever - they don't use a scoop, just an underhood inlet box sealed back to the plenum. Its probably externally insulated too - but I've never seen one up close.  

 
 Steve Metzger       Tucson, Arizona

Doug,

I'm not a scientist or engineer, but I understand the math.  I also get it that it would be difficult to measure air density changes with a change in velocity before the carb and while in motion, but do you think there could be an instrument that would have small enough increments to measure this change in the intake manifold (i.e. vacuum or boost)?

Location of the scoop is the quandary.  I cannot use headlight or radiator support openings for air induction.  I know it is not in a favorable position in the middle of the hood and rules will not allow me to raise it enough to perform like it would on a roadster or other small frontal area vehicle.

If I could measure the density change, I could develop confidence in one of the few changes I could make.  One suggestion by experienced racers would be to turn the scoop around and face the windshield where it is said to have greater pressure.  Another is to make the opening in the front of the scoop smaller than the body of the scoop (I've seen this on pro-stocker hoods, but I have no Idea why it would increase density due to increased velocity).

I know I could make one of these changes and use the performance as a guide, but that may not happen for some time.  Also the performance changes might be so small that other variables might have played a bigger role.  It may seem odd, but I only average about one run per meet.  There are other changes that have higher priority and I try to change only one thing per run (i.e. timing and gear ratios).

I am still on the steep side of the learning curve................Any thoughts from anyone would be appreciated (even you Roy!).

Charlie Burns Laton, Ca (South of Fresno)



BurnsRacing981@gmail.com

The air pressure developed by the forward movement of the car is called the dynamic or velocity pressure.  As a practical matter for "normal" air the equation is VP  = (V/4005) ^ 2   where VP is pressure measured in inches of water gauge "WG, V is the velocity of the car in Feet/second and ^ 2 means you square the result.  So at 60 MPH you can develop as much as 1.73 inches of water gauge pressure.  But the air scoop has to be in clean undisturbed air and the center of a hood is not a good place to get that condition.  The effect on the carburator is that the air is a little denser than air drawn out of the semi still air under the hood. 

Density is inversely proportional to the pressure.  1 atmosphere is 407 "WG (still air) so with a good hood scoop at 60 mph you would increase the density of the air going to the carb to (407 + 1.73)/407 or about  0.4%  which isn't much.  However at Ted's terminal speed of 135 MPH the density has increased by a little over 2%

BTW the manometer mentioned was probably a Dwyer Slack tube manometer,  here is their web site

http://www.dwyer-inst.com/Products/TOC.cfm?MainCategory_ID=294&iCurrentCategoryID=296

 

Doug T

The Highlands, Louisville, Ky.

Forced air will lean the mixture and simply requires richening up the carb.  Of course it will be overly rich when air is not being forced in.  My roadster at 135 mph requires fatter than normal jetting to compensate for the increase in air pressure at the carb at these speeds.

Lorena, Texas (South of Waco)

My wife used a "Manometer" to find Me!  LOL  

What I got for my British cars many years ago has cast into it "Synchro-test" but we always called it a "Uni-Syn". Close enough.

   God Bless.   Tim                           http://yblockguy.com/

350ci Y-Block FED "Elwood", 301ci Y-Block Unibody LSR "Jake", 312ci Y-Block '58 F-100, 338ci Y-Block powered Model A Tudor

tim@yblockguy.com  Visalia, California    Just west of the Sequoias

Yeah, well  - when I asked for one (a "Manometer") over at Detroit D (sent there by my fearless leader)  - they said they didn't have such a thing - but they did have this "Slack Tube" for $40. So the name is now stuck in my head....... It came rolled up in a tin  - like a fruitcake - and I thought "now this is going to be real fun....." 

My Dad made one in '68 to help a neighbor of ours set-up the dual carbs on his Triumph Spitfire. It was just a double U tube made out of aquarium tubing stapled on a plywood leftover. It worked (I think) but I know the fellow eventually bought a made for the purpose (Uni-Sync?) tool to do the job. 

 
 Steve Metzger       Tucson, Arizona

Steve,

    Manometer

Frank/Rebop

Bristol, In ( by Elkhart)