Profile Picture

Swap Out 3 Spd OD Trans for Standard 3 speed

Posted By YukonCor55 15 Years Ago
You don't have permission to rate!
Author
Message
YukonCor55
Posted 15 Years Ago
View Quick Profile
Supercharged

Supercharged (103 reputation)Supercharged (103 reputation)Supercharged (103 reputation)Supercharged (103 reputation)Supercharged (103 reputation)Supercharged (103 reputation)Supercharged (103 reputation)Supercharged (103 reputation)Supercharged (103 reputation)

Group: Forum Members
Last Active: 15 Years Ago
Posts: 103, Visits: 161
Hi gang,

  Sorry, I've been away for awhile.  During the layoff, I sold my 55 Fairlane so I could concentrate on my 55 Ranch Wagon.  Life's a little easier when you can focus your time, energy and $$ on a single project!!   Wink  I'm currently running a 3 spd OD behind the original Y-Block but the electrical circuit was so buggered up I decided to disable it.  While the T-Handle under the dash does look cool, I really have no desire to get the OD operating again.  Mechanically the tranny is fine.  I'd almost leave it as is except that I'm turning about 2800 RPM in 3rd gear at 50 mph.  I don't want to run the old 272 any harder than necessary.  Are there any 3 or 4 speed non OD trannys that would swap right in or is there some wizardy required?  I have no problem with cutting a hole in the floor for a shifter if necessary. 

As always, thanks for your time.

Best,

A.J.

South Jersey

SMSgt USAF Retired 
1955 Ford Ranch Wagon & a couple of old guitars...Life's Good!


Threaded View

Threaded View
Forum Post Swap Out 3 Spd OD Trans for Standard 3 speed By YukonCor55 ( 15 Years Ago )
Forum Post Your current gear box is like all manual gearboxes - it is a 1.00:1... By rick55 ( 15 Years Ago )
Forum Post Hey Rick; Would 3:89 gears be too low for hiway use with a 3 speed... By Old Y Block ( 15 Years Ago )
Forum Post I have the 3:56 diff from a '56 wagon in my Bird along with the... By joey ( 15 Years Ago )
Forum Post If your OD is functional you could just wire a switch for it and... By Y block Billy ( 15 Years Ago )
Forum Post [quote][b]Y block Billy (1/24/2010)[/b][hr]If your OD is functional... By YukonCor55 ( 15 Years Ago )
Forum Post If it has the original rear end in a wagon with od it would be a 4.27... By crenwelge ( 15 Years Ago )
Forum Post One hot wire to the solenoid from a switch under the dash is all you... By speedpro56 ( 15 Years Ago )
Forum Post [quote][b]speedpro56 (1/24/2010)[/b][hr]One hot wire to the solenoid... By charliemccraney ( 15 Years Ago )
Forum Post Frank Rice uses a later fully synchronized three speed. It seems to... By Ol Ford Guy ( 15 Years Ago )
Forum Post If you are going to run the OD with only a push pull switch there are... By marvh ( 15 Years Ago )
Forum Post I agree with those that say keep the OD and just power the solenoid.... By Doug T ( 15 Years Ago )
Forum Post If your interested I have a regular 3 speed tranny (actually a couple... By Oldmics ( 15 Years Ago )
Forum Post There is a reason the OD was automatic in operation. Manual shifting... By DANIEL TINDER ( 15 Years Ago )
Forum Post I appreciate all of the replies and advice. I think I'm going to wire... By YukonCor55 ( 15 Years Ago )
Forum Post I installed an overdrive unit on the tail end of a truck tranny and... By Y block Billy ( 15 Years Ago )
Forum Post

Anybody have a spare solinoid, I could use one?[/quote]...
By DANIEL TINDER ( 15 Years Ago )
Forum Post I put a OD in my 56 sedan with a 3.89 rear end gear. I used a $7.00... By popbreed ( 15 Years Ago )
Forum Post The 3:89 is to low for highway use. Thats one of the ratios that came... By speedpro56 ( 15 Years Ago )


Reading This Topic


Site Meter