Profile Picture

Intake Manifold Question

Posted By pendergrass 13 Years Ago
You don't have permission to rate!

Intake Manifold Question

Author
Message
pendergrass
Posted 13 Years Ago
View Quick Profile
Hitting on all eight cylinders

Hitting on all eight cylinders (6 reputation)Hitting on all eight cylinders (6 reputation)Hitting on all eight cylinders (6 reputation)Hitting on all eight cylinders (6 reputation)Hitting on all eight cylinders (6 reputation)Hitting on all eight cylinders (6 reputation)Hitting on all eight cylinders (6 reputation)Hitting on all eight cylinders (6 reputation)Hitting on all eight cylinders (6 reputation)

Group: Forum Members
Last Active: 11 Years Ago
Posts: 6, Visits: 312
Hello everyone. New guy here. Have a 56 vic with 292. I installed a 57 B intake on it with a 390 cfm holley. Runs great. Burnt the paint off the intake. Read some of the past topics and know there is a fix to this but haven't quite figured it out. One of the post talks about a different type of intake gasket to install and some about the heat tube. Do you just remove the tube and plug the holes in the intake? Is it OK to run it like it is or should it be fixed? Any help/suggestions greatly appreciated? Thanks Leon.

Leon        

Fallon,Nevada                                                                                                              

Threaded View

Threaded View
Forum Post Intake Manifold Question By pendergrass ( 13 Years Ago )
Forum Post I believe CASCO (Tbird supplier) has gaskets you are looking for. Make... By Don Woodruff ( 13 Years Ago )
Forum Post Being in warmer climes than most, removed the heat riser and blocked... By Tom Compton ( 13 Years Ago )
Forum Post You can cut a piece of thin metal and insert it in between the gasket... By MoonShadow ( 13 Years Ago )
Forum Post When you changed the intake and carb, did you upgrade the distributor... By Hoosier Hurricane ( 13 Years Ago )
Forum Post Thanks for the advice. I ordered new intake gaskets. I did not change... By pendergrass ( 13 Years Ago )
Forum Post [quote][b]pendergrass (6/21/2012)[/b][hr]Thanks for the advice. I... By aussiebill ( 13 Years Ago )
Forum Post Aussie, with this talk about blocking the hear crossover, I have... By lyonroad ( 13 Years Ago )
Forum Post Tee-Bird.com sells a "restricted" intake gasket under part # 9433A.I... By oldcarmark ( 13 Years Ago )
Forum Post [quote][b]lyonroad (6/23/2012)[/b][hr]Aussie, with this talk about... By aussiebill ( 13 Years Ago )
Forum Post Thanks Aussie, block them off with tin it is. By lyonroad ( 13 Years Ago )
Forum Post Thanks for all the advice. Yes, I have been on a few "boats". US NAVY... By pendergrass ( 13 Years Ago )
Forum Post Leon,

You should get by fine without the heat riser valve... By DANIEL TINDER ( 13 Years Ago )
Forum Post Sounds like someone installed the distributor 180 degrees out and just... By Hoosier Hurricane ( 13 Years Ago )
Forum Post One way to tell if you have the original no centrifugal advance type... By oldcarmark ( 13 Years Ago )
Forum Post Leon, It's gonna be tough to get Sea Sick in the desert! I spent some... By pegleg ( 13 Years Ago )
Forum Post [quote][b]pegleg (6/24/2012)[/b][hr]Leon, It's gonna be tough to get... By aussiebill ( 13 Years Ago )
Forum Post Frank,I hope that didn't stand for " super stock 409" By ecode ragtop ( 13 Years Ago )
Forum Post Tom, Nope, WWII era diesel electric submarine. The 405 (sorry about... By pegleg ( 13 Years Ago )
Forum Post an opposed piston engine. By charliemccraney ( 13 Years Ago )
Forum Post Sort of. They're a two stroke diesel. The upper crank led the lower... By pegleg ( 13 Years Ago )


Reading This Topic

Site Meter