|
Author
|
Message
|
|
Rono
|
|
|
Group: Forum Members
Last Active: Last Year
Posts: 1.3K,
Visits: 80.0K
|
Just a thought, but I wonder if my 2&1/2" dropped Granada spindles caused my interference between the oil pump and rack? I never knew anyone else that had this set-up to compare to. Rono
 Ron Lane, Meridian, ID
|
|
|
|
|
kansas
|
|
|
Group: Forum Members
Last Active: 8 Years Ago
Posts: 167,
Visits: 846
|
Its does turn tighter to the left than its does to the right but its not so much that its a problem also I did not have to do any shim/ oil pump to rack boot clearance is a good inch
|
|
|
|
|
Rono
|
|
|
Group: Forum Members
Last Active: Last Year
Posts: 1.3K,
Visits: 80.0K
|
Yes, I think it did, But I never drove the car with the stock steering. I started the tear down on the car as soon as I got it. I am surprised that Kansas did not need to modify the mounting of the rack. In addition to having to shim the motor and tranny upward 1/4" the rack had to be shimmed downward about 3/4" so the oil pump would not rest on the dust boot of the rack. Rono
Ron Lane, Meridian, ID
|
|
|
|
|
paul2748
|
|
|
Group: Forum Members
Last Active: 6 hours ago
Posts: 3.6K,
Visits: 497.6K
|
Ron and Kansas - how did the steering radius come out? Did it get wider?
54 Victoria 312; 48 Ford Conv 302, 56 Bird 312
Forever Ford
Midland Park, NJ
|
|
|
|
|
kansas
|
|
|
Group: Forum Members
Last Active: 8 Years Ago
Posts: 167,
Visits: 846
|
292 y block
|
|
|
|
|
Bob's 55
|
|
|
Group: Forum Members
Last Active: 11 Years Ago
Posts: 287,
Visits: 1.0K
|
^^^^ Kansas, what engine do you have? I notice on Wurthit.com site they have plenty of pictures but none with a Y-Block.
BOB
|
|
|
|
|
kansas
|
|
|
Group: Forum Members
Last Active: 8 Years Ago
Posts: 167,
Visits: 846
|
I have a wurthit designs rack set up in my 55 vic with a aod transmission The only thing that I had to do was go to a shorter oil filter and because a lack of feed back in steering I put in a pressure reducer in the power steering line
works great
|
|
|
|
|
Bob's 55
|
|
|
Group: Forum Members
Last Active: 11 Years Ago
Posts: 287,
Visits: 1.0K
|
Don't know much about it but I have seen some guys using the integral power steering from a Jeep Cherokee. I have seen an adapter plate that bolts onto the frame in the stock position occasionally on ebay.
BOB
|
|
|
|
|
lyonroad
|
|
|
Group: Forum Members
Last Active: 10 Years Ago
Posts: 703,
Visits: 3.1K
|
slick56 (2/6/2014)
Thanks Ted and Steve, i think there was a post on here regarding fitting an Isuzu (?) steering box.Will do some more homework...
.The Borgeson power steering box is an Isuzu unit. I have one on my car, but not tested as the car is still in production. It requires a hydraulic clutch set up and results in minor interference with 1957 and later exhaust manifolds. I cured this with a slight angle milling of the manifold flange. These boxes are used extensively on early Mustangs. Also there is a fellow on ebay that sells an adapter that will allow you to to do your own setup to avoid the high Borgeson cost.
Mark
1956 Mercury M100
1955 Ford Fairlane Club Sedan
Delta, British Columbia
|
|
|
|
|
Rono
|
|
|
Group: Forum Members
Last Active: Last Year
Posts: 1.3K,
Visits: 80.0K
|
I have a rear mounted power R&P set-up in my 56 Customline, but I have to say it was a nightmare and without help from an engineering professor at Boise State University, I probably couldn't have made it happen. About 7 or 8 years ago there was a guy,Rick Wurth,(Wurthit Designs) who advertised a rear mounted R&P set-up for 55-56 Ford passenger cars using a Cavalier rack that mounted with his kit. The big problems that were encountered were that he did his mock-up only on automatic, non Y Block powered cars. So, after we had the rack mounted and put the motor in, the oil pump rested squarely on top of the rack requiring the motor and tranny to be shimmed up 1/4" off the motor mounts. As Ted stated, the angle coming off the column was extreme and a complicated heim bearing and bracket had to be fabricated to ease the angle and to get around the clutch linkage. We did finally get it all to work and the car steers very easily. I have all the pictures of the nightmare trial and error process when we were building the car, but they are on my other computer which is packed-up for the move. My final words on this would be "don't try this at home" 
Rono
Ron Lane, Meridian, ID
|
|
|
|