I thought the engine guys would get a kick out of this, I know I did. A 91 year old gentelman came into our shop last week and wanted to know if we could bore an engine for him, I said "Yes, what kind of engine?"

Well here is what he brought in. It's a 1902 Rambler, single cylinder OHV, 5" bore 6" stroke (117ci is what I came up with) He said it was hard to start and needed to have a new oversize piston. We didn't have one on the shelf, and Egge couldn't make one with the correct comp. hieght, it's probably only 4:1 as it is. So it gets a sleeve and a new set of rings.

Here are some pictures, check out the rod cap. Notice I put a Y-Block in the pictures so

I'm not totaly off subject.

 

   God Bless.   Tim                           http://yblockguy.com/

350ci Y-Block FED "Elwood", 301ci Y-Block Unibody LSR "Jake", 312ci Y-Block '58 F-100, 338ci Y-Block powered Model A Tudor

tim@yblockguy.com  Visalia, California    Just west of the Sequoias

Neat con rod! Cast iron pistons?

Frank/Rebop

Bristol, In ( by Elkhart) 

Great story, great pictures, makes me feel young..

Brother and I own/operate 1957 Ford Fairlane 312/4x2 and two 1963 Falcons 302 rollers carburated 600cfm, FE427 sitting in shed..

Tim: Did anyone ask about the car it goes in?

Paul

I haven't seen the car yet, but the old guy said I could come look at it when he gets it back together. I imagine it is something like a "Curved Dash Olds" he did say it has a tiller bar instead of a steering wheel. When I do go see the car I will take pictures and post them.

   God Bless.   Tim                           http://yblockguy.com/

350ci Y-Block FED "Elwood", 301ci Y-Block Unibody LSR "Jake", 312ci Y-Block '58 F-100, 338ci Y-Block powered Model A Tudor

tim@yblockguy.com  Visalia, California    Just west of the Sequoias

Pretty neat Tim, I like any of that old stuff like that, tractors, stationary motors, etc.

                                               Michael

Michael

Sandy Valley, NV

OK Guys, I have a picture of the car. It was brought to Me by the old Man, I hope to go see the car in person and take better pictures and some video to post on YouTube.

You can see the crank just below the seat, that's the starter.

   God Bless.   Tim                           http://yblockguy.com/

350ci Y-Block FED "Elwood", 301ci Y-Block Unibody LSR "Jake", 312ci Y-Block '58 F-100, 338ci Y-Block powered Model A Tudor

tim@yblockguy.com  Visalia, California    Just west of the Sequoias

I think this has happened to all of us... as a young man we all were keen on new cars, then we got a little more age and focused to a bit older cars and used those as a daily drivers and now after few years, fresh cars just don't get our attention . Every old thing is interesting ( exept old ladies ) and is worth atleast a thought .

BTW... How long is that rod?

 Seppo from Järvenpää, Finland
www.hollowheads.net (just click the hole in the head to proceed)

Hollow Head (1/10/2009)

---

Every old thing is interesting ( exept old ladies ) and is worth at least a thought .

BTW... How long is that rod?

Seppo, You'll eventually find that some old ladies can be very interesting! Some of them can actually hold an intelligent conversation also.

Frank/Rebop

Bristol, In ( by Elkhart) 

the thing i find as interesting as the engine is the guys 91 & restoring this thing hell if i make it too 91 i think i will be lucky to remember i even had a y-block.

frank what do mean a women that you can have a conversation with i couldnt think of anything worse.

moz. geelong victoria australia.

graduate 1980, bus, truck, car, hot rod, boat, submarine, hovercraft, hydrafoil, firetruck, mobile home, jet, helicopter, cruise ship, motorcycle, bicycle, santa's sleigh, clock, alloy bullbar, alloy fuel tank, lens, dr who's tardis, matter - anti matter warp drive buffer & y-block lover