Profile Picture

Clutch/Trans. alignment

Posted By DANIEL TINDER 16 Years Ago
You don't have permission to rate!

Clutch/Trans. alignment

Author
Message
DANIEL TINDER
Posted 16 Years Ago
View Quick Profile
Supercharged

Supercharged (2.4K reputation)Supercharged (2.4K reputation)Supercharged (2.4K reputation)Supercharged (2.4K reputation)Supercharged (2.4K reputation)Supercharged (2.4K reputation)Supercharged (2.4K reputation)Supercharged (2.4K reputation)Supercharged (2.4K reputation)

Group: Forum Members
Last Active: Yesterday
Posts: 1.7K, Visits: 154.0K
Something just occurred to me (a bit late now), but when bolting up a line-bored engine to a stock/orig. bellhousing/trans. assembly, since the crank/flywheel/clutch center is now likely a bit higher in the block (?), would this minor misalignment be significant? If so, what is the standard procedure to compensate?

6 VOLTS/POS. GRD. NW INDIANA

Threaded View

Threaded View
Forum Post Clutch/Trans. alignment By DANIEL TINDER ( 16 Years Ago )
Forum Post Daniel; I line honed my block and used the stock bellhousing with a... By Rono ( 16 Years Ago )
Forum Post [quote][b]Rono (12/9/2009)[/b][hr]Daniel;

I line honed my... By ejstith ( 16 Years Ago )
Forum Post I seriously doubt that very small amount of offset would ever be any... By Duck ( 16 Years Ago )
Forum Post [quote]I seriously doubt that very small amount of offset would ever... By DANIEL TINDER ( 16 Years Ago )
Forum Post Daniel, why put yourself through it? .003 or 004 thou wouldnt even... By aussiebill ( 16 Years Ago )
Forum Post I don't think the line bore would upset anything, but I like to put a... By crenwelge ( 16 Years Ago )
Forum Post Bill,

Pro: 1. With bellhousing removed, it would likely... By DANIEL TINDER ( 16 Years Ago )
Forum Post Daniel: Since you seem inclined to check, I have a suggestion. Take... By Hoosier Hurricane ( 16 Years Ago )
Forum Post The factory manual has a proceedure to check run-out between the crank... By John Mummert ( 16 Years Ago )
Forum Post John, sorry to cut in, received the rocker setup today, they are nice!... By aussiebill ( 16 Years Ago )
Forum Post [quote][b]John Mummert (12/10/2009)[/b][hr]The factory manual has a... By DANIEL TINDER ( 15 Years Ago )
Forum Post John,

55 shop manual spec. is .010 max. indicator variation... By DANIEL TINDER ( 16 Years Ago )
Forum Post The way we center clutch housings on 855 Cummins engines is to dial... By crenwelge ( 16 Years Ago )
Forum Post I would shim it first and get the parallel right first and check the... By crenwelge ( 15 Years Ago )
Forum Post [quote][b]crenwelge (6/6/2010)[/b][hr]I would shim it first and get... By DANIEL TINDER ( 15 Years Ago )
Forum Post All but the softest aluminum should work. Even then it can take years... By charliemccraney ( 15 Years Ago )
Forum Post [quote][b]charliemccraney (6/7/2010)[/b][hr]All but the softest... By DANIEL TINDER ( 15 Years Ago )
Forum Post Interesting. Halving the parallel face runout with shims doubled the... By DANIEL TINDER ( 15 Years Ago )
Forum Post [quote][b]DANIEL TINDER (6/8/2010)style. With my luck, once the bore... By DANIEL TINDER ( 15 Years Ago )
Forum Post Dan, The center of the crank may not necessarily be moved... By pegleg ( 15 Years Ago )
Forum Post Frank, are you trying to say that Detroit wasn't putting out precision... By John Mummert ( 15 Years Ago )
Forum Post Mebbie!!:w00t::w00t: By pegleg ( 15 Years Ago )


Reading This Topic

Site Meter