Group: Forum Members
Last Active: 3 Months Ago
Posts: 813,
Visits: 3.4K
|
Since I was taking some parts off a 56 for a friend I grabbed a complete set of plug wire holders since I dont think both of my motors have a complete set of holders,this car had two flat 4 wire rubber holders with little straps around them for the wires on the drivers side of the motor and since its been so long since I seen them is this correct.
Butchering up everything I can get my hands on in Dayton Ohio
|
Group: Forum Members
Last Active: 2 Years Ago
Posts: 217,
Visits: 6.7K
|
Hi Usually there are flat four holders at the back of the motor and square four holders under the exhaust manifolds at the rear, bottom corners of the heads. Check out page 26 of this on line catalog www.prestigethunderbird.com Barry
|
Group: Forum Members
Last Active: 10 Years Ago
Posts: 349,
Visits: 1.3K
|
If I understand you correctly, yes, those be them...
BOO- YA!!! 
|
Group: Forum Members
Last Active: 3 Months Ago
Posts: 813,
Visits: 3.4K
|
I am suprised they were still on the car due to being a pain to reinstall with new wires,the last set I installed took me about 3 hours and will buy good wires and install when the motor is on the stand or before the manifolds go on.
Butchering up everything I can get my hands on in Dayton Ohio
|
Group: Forum Members
Last Active: 7 Years Ago
Posts: 1.6K,
Visits: 5.2K
|
What do yopu mean a pain to install? If you are still doing your own work you must be a contorsoinist also?
 55 Vicky & customline 58 Rack Dump, 55 F350 yard truck, 57 F100 59 & 61 P 400's, 58 F100 custom cab, 69 F100, 79 F150, 82 F600 ramp truck, 90 mustang conv 7 up, 94 Mustang, Should I continue?
|
Group: Forum Members
Last Active: 1 hour ago
Posts: 3.6K,
Visits: 497.6K
|
If your using the 7mm or 8mm wire on new holders, these can be a real hassle getting them through the holes or, if you take them apart to insert the wires, the clips are very hard to close up. I did it ok with one set because, I think, they were originl holders. Not as successful with a reproduction set, I ended up making new inserts out of nylon in place of the rubber.
These were for new wires, with one end unfinished.
54 Victoria 312; 48 Ford Conv 302, 56 Bird 312 Forever Ford Midland Park, NJ
|
Group: Forum Members
Last Active: 9 Years Ago
Posts: 153,
Visits: 2.2K
|
Barry L (3/19/2011)
Hi Usually there are flat four holders at the back of the motor and square four holders under the exhaust manifolds at the rear, bottom corners of the heads. Check out page 26 of this on line catalog http://www.prestigethunderbird Barry I couldn't get the link to work. I would like to look at the diagram. Is it just me and my computer?
Gerald Ingram aka "Gritsngumbo" Monroe, LA LITTLE RED: 64 Ford F100 Short Bed Styleside BIG RED: 63 Ford F100 Long Bed Unibody BBW RED: 61 Ford F100 BBW Long Bed Custom Cab Unibody BIG “UN: 63 F250 Longbed Flareside CREW CAB: 63 F100 "Stageway" Crew Cab w/Long "Wrong" Bed
|
Group: Forum Members
Last Active: 1 hour ago
Posts: 3.6K,
Visits: 497.6K
|
wouldn't work for me either - just type in the url, it works. you can leave off the http//
54 Victoria 312; 48 Ford Conv 302, 56 Bird 312 Forever Ford Midland Park, NJ
|
Group: Forum Members
Last Active: 3 Months Ago
Posts: 813,
Visits: 3.4K
|
The last time I put plug wires on the original 272 I used cut to fit wires and will do the same when the 292 goes togather.
Butchering up everything I can get my hands on in Dayton Ohio
|
Group: Forum Members
Last Active: 2 Years Ago
Posts: 217,
Visits: 6.7K
|
Hi I've edited the above link in my first post..should work now. Barry
|