Profile Picture

Damn oil leak!

Posted By Talkwrench 14 Years Ago
You don't have permission to rate!
Author
Message
Talkwrench
Posted 14 Years Ago
View Quick Profile
Supercharged

Supercharged (1.6K reputation)Supercharged (1.6K reputation)Supercharged (1.6K reputation)Supercharged (1.6K reputation)Supercharged (1.6K reputation)Supercharged (1.6K reputation)Supercharged (1.6K reputation)Supercharged (1.6K reputation)Supercharged (1.6K reputation)

Group: Forum Members
Last Active: 4 Years Ago
Posts: 898, Visits: 23.2K
Advice on this oil leak guys.. I fixed the valley pan leak and now I have this leak to deal with, just not sure of where/ what it might be .. Im saying rear mainErmm but behind the inspection cover the ring gear / converter is quite dry. The leak seems about half way up the block [both sides as you can see] and between the trans. the oil pump seems dry too.. all runs down and wet at the bottom , the leak is quite bad, will start dripping on the ground after a short run.

http://forums.y-blocksforever.com/Uploads/Images/02c74785-3ce2-4b80-a66c-f31f.jpg

"Came too close to dying to stop living now!"

Threaded View

Threaded View
Forum Post Damn oil leak! By Talkwrench ( 14 Years Ago )
Forum Post Do you have any pictures of the top of the engine?
...
By The Master Cylinder ( 14 Years Ago )
Forum Post You can pretty much rule out the valley pan, it would not produce a... By Hoosier Hurricane ( 14 Years Ago )
Forum Post [quote][b]Hoosier Hurricane (5/15/2011)[/b][hr]You can pretty much... By 46yblock ( 14 Years Ago )
Forum Post If all else fails to locate your oil leak you can buy a " blacklight"... By Pete 55Tbird ( 14 Years Ago )
Forum Post Is the block, behind the heads dry? Take a look on the engine from... By lovefordgalaxie ( 14 Years Ago )
Forum Post Valley pan , bolt holes, dissy gasket, all the top stuff is sealed... By Talkwrench ( 14 Years Ago )
Forum Post Dissy gasket? No seal or gasket is used.Dist is installed metal to... By oldcarmark ( 14 Years Ago )
Forum Post Do you have the gasket between the block and the oil pump? By Ted ( 14 Years Ago )
Forum Post My distributor has a rubber o ring that seals it, but I never had a... By lovefordgalaxie ( 14 Years Ago )
Forum Post Its only a fine gasket, And even when I had the other dissy with the O... By Talkwrench ( 14 Years Ago )
Forum Post Have you figured out your oil leak yet? I seem to have the same... By Dave V ( 14 Years Ago )
Forum Post At this stage, after having another look I believe it to be a rear... By Talkwrench ( 14 Years Ago )
Forum Post There's a "freeze plug" at the back of the Cam bore, above the rear... By pegleg ( 14 Years Ago )
Forum Post Before you pull the engine to replace the rear seal get some dye and a... By Pete 55Tbird ( 14 Years Ago )
Forum Post [quote][b]Pete 55Tbird (5/28/2011)[/b][hr]Before you pull the engine... By The Master Cylinder ( 14 Years Ago )
Forum Post I am aware of that cam plug... hoping its not it, its unlikely the... By Talkwrench ( 14 Years Ago )
Forum Post I can't even recognize anything in those pictures.....it is way too... By Big6ft6 ( 14 Years Ago )
Forum Post I think I have an oil leak too, can anyone tell where it is coming... By Big6ft6 ( 14 Years Ago )
Forum Post [quote][b]Big6ft6 (6/4/2011)[/b][hr]I think I have an oil leak too,... By rgrove ( 14 Years Ago )
Forum Post That looks like good rust prevention around salt happy Madtown Nate By 55vickey ( 14 Years Ago )
Forum Post [quote][b]55vickey (6/5/2011)[/b][hr]That looks like good rust... By Big6ft6 ( 14 Years Ago )
Forum Post NOW THATS FUNNY:P By Talkwrench ( 14 Years Ago )
Forum Post Well after fitting the new rear main seal seems its a failure ; o (... By Talkwrench ( 14 Years Ago )
Forum Post Are you dealing with a 292 or a 312? There are two different... By Ted ( 14 Years Ago )
Forum Post 292 ,Ted I see no evidence of it being a 312 [not sure if that would... By Talkwrench ( 14 Years Ago )
Forum Post [quote][b]Talkwrench (7/16/2011)[/b][hr]292 ,Ted I see no evidence of... By aussiebill ( 14 Years Ago )
Forum Post Ditto on what Bill said. I was referring to using the 292 seal... By Ted ( 14 Years Ago )
Forum Post Thanks guys, I knew what you ment Ted, my answer was when fitting the... By Talkwrench ( 14 Years Ago )
Forum Post T.W: Does your engine have the plug wire loom brkts at the rear of the... By PF Arcand ( 14 Years Ago )
Forum Post Ive checked all those initially, all in all ok ... By Talkwrench ( 14 Years Ago )


Reading This Topic


Site Meter