I managed to get one in but will look at the inner panel for the other. Isn't the fastener still up and behind the door hinge pocket? Chuck



Y's guys rule!
Looking for McCullouch VS57 brackets and parts. Also looking for 28 Chrysler series 72 parts. And early Hemi parts.

MoonShadow, 292 w/McCulloch, 28 Chrysler Roadster, 354 Hemi)
Manchester, New Hampshire

The very rear part of the inner fender that is behind the wheels is removable and that is how I was able to get to those bolts in my 55


Butchering up everything I can get my hands on in Dayton Ohio

Thanks Alan. That sounds like a workable solution. When I came in tonight from the shop I was thinking of drilling a new hole 6-8" forward of the door edge. There is one spot there I can reach. Better solution is the door jamb hole. I'll try that one tomorrow. Chuck

Y's guys rule!
Looking for McCullouch VS57 brackets and parts. Also looking for 28 Chrysler series 72 parts. And early Hemi parts.

MoonShadow, 292 w/McCulloch, 28 Chrysler Roadster, 354 Hemi)
Manchester, New Hampshire

I was able to get a 1/4" drive socket on the fender moulding nut closest to the door jam by drilling an access hole in the sheet metal  interior kick panel under the cardboard trim panel.  I located the correct place to drill the hole in the kick panel by first drilling a small hole from the outside in.  I then enlarged the hole on the inside to about 1/2" diameter so I could get a socket with a long extension on the nut.  You can then get a 1/2" rubber plug to fill the access hole and none of this will be seen when the cardboard trim panel is in place.  Good luck, Alan S. Freeman

I've two different push in's and neither will seat deep enough in the hole. Bill, I didn't get the picture text came though with no subject but the picture doesn't show up.



Y's guys rule!
Looking for McCullouch VS57 brackets and parts. Also looking for 28 Chrysler series 72 parts. And early Hemi parts.

MoonShadow, 292 w/McCulloch, 28 Chrysler Roadster, 354 Hemi)
Manchester, New Hampshire

On my 54, I had to use a push in clip for the last fender clip.


54 Victoria 312;  48 Ford Conv 302, 56 Bird 312
Forever Ford
Midland Park, NJ

I'll have to check. I haven't had my phone on yet today. Chuck

Y's guys rule!
Looking for McCullouch VS57 brackets and parts. Also looking for 28 Chrysler series 72 parts. And early Hemi parts.

MoonShadow, 292 w/McCulloch, 28 Chrysler Roadster, 354 Hemi)
Manchester, New Hampshire

Did you get my pic I texted you?

55 Vicky & customline

58 Rack Dump, 55 F350 yard truck, 57 F100

59 & 61 P 400's, 58 F100 custom cab, 69 F100, 79 F150, 82 F600 ramp truck, 90 mustang conv 7 up, 94 Mustang, Should I continue?

Thanks Bill. I was wondering about that. I bought a set of new clips and they were all bolt on. Other than this last one the set worked out perfectly. I can see where this one requires a snap in. I'll see what I can find. Chuck

Y's guys rule!
Looking for McCullouch VS57 brackets and parts. Also looking for 28 Chrysler series 72 parts. And early Hemi parts.

MoonShadow, 292 w/McCulloch, 28 Chrysler Roadster, 354 Hemi)
Manchester, New Hampshire

Correction, its above the fender bolt, not below.

55 Vicky & customline

58 Rack Dump, 55 F350 yard truck, 57 F100

59 & 61 P 400's, 58 F100 custom cab, 69 F100, 79 F150, 82 F600 ramp truck, 90 mustang conv 7 up, 94 Mustang, Should I continue?