|
Author
|
Message
|
|
MoonShadow
|
Posted 10 Years Ago
|
|
Group: Forum Members
Last Active: Yesterday
Posts: 4.6K,
Visits: 38.1K
|
I'm putting the chrome trim back on my Vicky and have a question. On the front fender spear the rear fastener is in a place that I can't figure out how to get to it. The new trim set has a clip with a bolt and needs a nut on the back. I can't reach it, can't see it and don't see a way to access it. HELP! There must be a trick to it that I'm missing. Chuck
Y's guys rule!
Looking for McCullouch VS57 brackets and parts. Also looking for 28 Chrysler series 72 parts. And early Hemi parts.
 
MoonShadow, 292 w/McCulloch, 28 Chrysler Roadster, 354 Hemi)
Manchester, New Hampshire
|
|
|
|
|
DryLakesRacer
|
|
|
Group: Forum Members
Last Active: Last Year
Posts: 1.7K,
Visits: 340.0K
|
I replaced mine. As I remember the test fit the nuts/screws then tightened them with either a ignition wrench while hold the headlight rim in my hand. Are yours nuts or screws.?. If they are screws bottom out a nut tight on the screw and then use the ignition wrench on it...good luck
56 Vic, B'Ville 200 MPH Club Member, So Cal.
|
|
|
|
|
MoonShadow
|
|
|
Group: Forum Members
Last Active: Yesterday
Posts: 4.6K,
Visits: 38.1K
|
I was able to get the front ones by removing the headlight. The problem is on the other end by the door. Chuck
Y's guys rule!
Looking for McCullouch VS57 brackets and parts. Also looking for 28 Chrysler series 72 parts. And early Hemi parts.
MoonShadow, 292 w/McCulloch, 28 Chrysler Roadster, 354 Hemi)
Manchester, New Hampshire
|
|
|
|
|
Y block Billy
|
|
|
Group: Forum Members
Last Active: 7 Years Ago
Posts: 1.6K,
Visits: 5.2K
|
Looking at the fenders I have here, the end ones by the door are snap in clips, otherwise it looks like you would have to pull the fender out to get at it if you are using nut and bolt because it is right below the center fender mounting bolt that bolts the fender to the pillar. The end door ones are behind the rubber door seal, hope you didnt install your seals already!
I can text you a pic of it!
 55 Vicky & customline 58 Rack Dump, 55 F350 yard truck, 57 F100 59 & 61 P 400's, 58 F100 custom cab, 69 F100, 79 F150, 82 F600 ramp truck, 90 mustang conv 7 up, 94 Mustang, Should I continue?
|
|
|
|
|
Y block Billy
|
|
|
Group: Forum Members
Last Active: 7 Years Ago
Posts: 1.6K,
Visits: 5.2K
|
Correction, its above the fender bolt, not below.
55 Vicky & customline 58 Rack Dump, 55 F350 yard truck, 57 F100 59 & 61 P 400's, 58 F100 custom cab, 69 F100, 79 F150, 82 F600 ramp truck, 90 mustang conv 7 up, 94 Mustang, Should I continue?
|
|
|
|
|
MoonShadow
|
|
|
Group: Forum Members
Last Active: Yesterday
Posts: 4.6K,
Visits: 38.1K
|
Thanks Bill. I was wondering about that. I bought a set of new clips and they were all bolt on. Other than this last one the set worked out perfectly. I can see where this one requires a snap in. I'll see what I can find. Chuck
Y's guys rule!
Looking for McCullouch VS57 brackets and parts. Also looking for 28 Chrysler series 72 parts. And early Hemi parts.
MoonShadow, 292 w/McCulloch, 28 Chrysler Roadster, 354 Hemi)
Manchester, New Hampshire
|
|
|
|
|
Y block Billy
|
|
|
Group: Forum Members
Last Active: 7 Years Ago
Posts: 1.6K,
Visits: 5.2K
|
Did you get my pic I texted you?
55 Vicky & customline 58 Rack Dump, 55 F350 yard truck, 57 F100 59 & 61 P 400's, 58 F100 custom cab, 69 F100, 79 F150, 82 F600 ramp truck, 90 mustang conv 7 up, 94 Mustang, Should I continue?
|
|
|
|
|
MoonShadow
|
|
|
Group: Forum Members
Last Active: Yesterday
Posts: 4.6K,
Visits: 38.1K
|
I'll have to check. I haven't had my phone on yet today. Chuck
Y's guys rule!
Looking for McCullouch VS57 brackets and parts. Also looking for 28 Chrysler series 72 parts. And early Hemi parts.
MoonShadow, 292 w/McCulloch, 28 Chrysler Roadster, 354 Hemi)
Manchester, New Hampshire
|
|
|
|
|
paul2748
|
|
|
Group: Forum Members
Last Active: Yesterday
Posts: 3.6K,
Visits: 497.6K
|
On my 54, I had to use a push in clip for the last fender clip.
54 Victoria 312; 48 Ford Conv 302, 56 Bird 312
Forever Ford
Midland Park, NJ
|
|
|
|
|
MoonShadow
|
|
|
Group: Forum Members
Last Active: Yesterday
Posts: 4.6K,
Visits: 38.1K
|
I've two different push in's and neither will seat deep enough in the hole. Bill, I didn't get the picture text came though with no subject but the picture doesn't show up.
Y's guys rule!
Looking for McCullouch VS57 brackets and parts. Also looking for 28 Chrysler series 72 parts. And early Hemi parts.
MoonShadow, 292 w/McCulloch, 28 Chrysler Roadster, 354 Hemi)
Manchester, New Hampshire
|
|
|
|