Profile Picture

More teapot woes

Posted By 56_Fairlane 11 Years Ago
You don't have permission to rate!
Author
Message
56_Fairlane
Question Posted 11 Years Ago
View Quick Profile
Supercharged

Supercharged (1.3K reputation)Supercharged (1.3K reputation)Supercharged (1.3K reputation)Supercharged (1.3K reputation)Supercharged (1.3K reputation)Supercharged (1.3K reputation)Supercharged (1.3K reputation)Supercharged (1.3K reputation)Supercharged (1.3K reputation)

Group: Forum Members
Last Active: 6 Months Ago
Posts: 575, Visits: 14.6K
Took my 56 for a nice drive or at least I was hoping it would have turned out that way. It was running really nicely until it sputtered out in a left turn lane. It wouldn't restart. A couple of really nice guys with tow straps helped pull me into a parking lot. The carb looked a little wet so I let it air out with the throttles open for a few minutes. Tried to restart and I could see gas start gushing from the side of the carb, The air cleaner was back on at this point so I couldn't see exactly where it came from as I quickly went to shut it off but it sputtered out on it's own. To me this sounds like a float issue that let it overflow.
If it is, is this something fairly simple that can be looked into?


~DJ~ AKA "Bleach"
1956 Ford Fairlane Town Sedan 30K original miles

Threaded View

Threaded View
Forum Post More teapot woes By 56_Fairlane ( 11 Years Ago )
Forum Post It could also be the gasket under the big screw that holds the needle... By speedpro56 ( 11 Years Ago )
Forum Post Sorry to read of your problem. I remember our families original 56 and... By DryLakesRacer ( 11 Years Ago )
Forum Post Couple of suggestions.When these Carbs are rebuilt usually the little... By oldcarmark ( 11 Years Ago )
Forum Post Very few carburetors are as sensitive to fuel pressure and leaks as... By Daniel Jessup ( 11 Years Ago )
Forum Post I haven't had a chance to check the big screw again. I didn't really... By 56_Fairlane ( 11 Years Ago )
Forum Post You might check to see if the vent holes in the top of the carb are... By slumlord444 ( 11 Years Ago )
Forum Post Just so I know which are the vent holes on this carb, is there a good... By 56_Fairlane ( 11 Years Ago )
Forum Post I don't have an image to show you right now, but the vent holes he is... By Daniel Jessup ( 11 Years Ago )
Forum Post Yes I have the 56. IIRC, I think that washer shown is missing. I... By 56_Fairlane ( 11 Years Ago )
Forum Post To be honest, I am not exactly sure why Ford/Holley has that washer... By Daniel Jessup ( 11 Years Ago )
Forum Post [quote][b]Daniel Jessup (7/21/2014)[/b][hr]Seems I remember a video... By charliemccraney ( 11 Years Ago )
Forum Post This is probably more than you asked for but I will take a chance... By Jimz Bird ( 11 Years Ago )
Forum Post Thanks Jim. So far, Mike's looks like the best resource for the carb.... By 56_Fairlane ( 11 Years Ago )
Forum Post No expert but your problem sounds exactly like what happened to me not... By Meandean ( 11 Years Ago )
Forum Post I'll have to open up the top and check the bowl, float and seat. The... By 56_Fairlane ( 11 Years Ago )
Forum Post I think he's talking about a different washer under the air cleaner... By 56_Fairlane ( 11 Years Ago )
Forum Post I believe that was the video I was referring to, thank you Charlie.... By Daniel Jessup ( 11 Years Ago )
Forum Post I don't plan on tearing into the teapot any further. It's going back... By 56_Fairlane ( 11 Years Ago )
Forum Post When I drove my '56 home it had the teapot on board - and the... By GREENBIRD56 ( 11 Years Ago )
Forum Post By golly Steve, that's what I was hoping I could when I bought the... By 56_Fairlane ( 11 Years Ago )
Forum Post 56---If you do the swap and don't want to use rubber fuel lines invest... By DryLakesRacer ( 11 Years Ago )
Forum Post Thanks for the tip. I've already ordered the last few parts I need... By 56_Fairlane ( 11 Years Ago )
Forum Post I just noticed this evening when trying a dry fit, the Autolite... By 56_Fairlane ( 11 Years Ago )
Forum Post Will a thick phenolic spacer help it clear maybe? By Daniel Jessup ( 11 Years Ago )
Forum Post No, I mocked one up with an aluminum adapter and it still was binding.... By 56_Fairlane ( 11 Years Ago )
Forum Post The T-bird guys often use a replacement water control valve that is... By GREENBIRD56 ( 11 Years Ago )
Forum Post I don’t recall seeing any ’57 Ford V8’s using the intake mounted... By Ted ( 11 Years Ago )
Forum Post When looking for a cable heater control valve make sure it works in... By MoonShadow ( 11 Years Ago )
Forum Post Heater Control Valve Something like this will work in line from the... By Jimz Bird ( 11 Years Ago )
Forum Post So it sounds I would need the control valve used in the 57's full... By 56_Fairlane ( 11 Years Ago )
Forum Post [quote][b]56_Fairlane (7/23/2014)[/b][hr]...... Ted, do you have a... By Ted ( 11 Years Ago )
Forum Post I did a bit of googling and it looks like all that goes in the hole in... By 56_Fairlane ( 11 Years Ago )
Forum Post Thanks. It's kind of hard to get a good look at the actual fitting and... By 56_Fairlane ( 11 Years Ago )


Reading This Topic


Site Meter